Log In / Register / Contacts Us / Chinese  
 
Quick link
Technical Support
Project Management
Training
Warranty
Configuration Examples
FXS ports Configuration
FXO ports Configuration
FXS/FXO ports Configuration
EIA20X work with Asterisk  Configuration
EIA20X work with Cisco Configuration
EID3000 work with EIA20X Configuration
EID3000 R2/H.323 Configuration
EID3000 PRI/SIP Configuration
EID3000 SS7/H.323 Configuration
 
 

 

 

 
Home > Products> FAQ

FAQ

1 Can Aliwei IAD support H323, SIP and MGCP at the same time, same  interface?
2 Can I configure any interface to run any service?
3 Can I register, send calls to fqdn or only IPs?
4 Is stun or outbound proxy for SIP supported?
5 How to configure FXO detecte BusyTone 450/350 0/350?
6 How to config busyTone?
7 How to config RingBackTone?
8 How to change ringing?
9 How to adjust gain and solve echo (pdf)?
10 How long the line from fxs ports to phone set?
11 for SIP: which softswitch Aliwei digital gateway are sure to work with?
12 for SS7 : which switches Aliwei digital gateway have tested or worked with?
13 Does Aliwei IAD support Pulse dialing?
14 EIA20X Configuration examples:
   
   
1 Aliwei IAD support three protocols, If customer like to use three protocols at the same time. It is needed to upgrade a new version.   
   
2 Aliwei IAD can support these protocols, customer can configure according the need.
   
3 Aliwei IAD upport both of them, for example:
     <1>by ip
              sip-ua
              ip local 13.1.11 .22 registrar ipv4:209.188.239.106
              mode through
              ring-mode ring-mode-183
  
     <2>by fqdn
              sip-ua
              ip local 13.1.11.23
              registrar dns:sipx.company.com
              mode through
              ring-mode ring-mode-183
   
4 Support out -bound-proxy. For example:
       sip-ua
            ip local 13.1.11.23
            registrar ipv4:209.188.239.106
            mode through
            out-bound-proxy ipv4:209.188.239.106
            ring-mode ring-mode-183
      
out-bound-proxy also can be configured as out-bound-proxy dns:sipx.company.com
   
5 Config at voice-port mode

busytone 425 200 200

busytone frequency/ RingOnTime/ RingOffTime

   
6 config at global configuration mode

busy = 425/200 0/200

tone-generate busy f1 425 f 2 0 f 3 0 f 4 0 on-time 200 off-time 200 numCad 1 repCounter 0 on_time_2 0 off_time_2 0 on_time_3 0 off_time_3 0 tonePwr1 20 tonePwr2 20 tonePwr3 20 tonePwr4 20

   
7 RingBackTone

config at global configuration mode

ringback = 425/1500 0/3000

tone-generate ring-back f1 425 f 2 0 f 3 0 f 4 0 on-time 1500 off-time 3000 numCad 1 repCounter 0 on_time_2 0 off_time_2 0 on_time_3 0 off_time_3 0 tonePwr1 20 tonePwr2 20 tonePwr3 20 tonePwr4 20

   
8 config at the voice-port mode

commands:

ring-mode frequence <ringing frequency> default is 25Hz

ring-off <RingOffTime> defaut is 4000ms

ring-on <RingOnTime> default is 1000ms

voltage <Ringing voltage> default is 90V

wave <Ringing wave> default is Sine wave>

Press ? and get the range value.

   
10 The line phone from fxs ports to phone set is 3 to 5 km . It is needed to add a driver if the customer need more long line.
   
11 Cisco Huawei, ZTE, Bell , Alcatel AVAYA, Siemens,Nokia etc.
   
12 Cisco, Huawei, Alcatel, Nortel, lucent,Siemens, Nokia etc.
   
13 Yes, Aliwei IAD have software version can support pulse dialing
   
Aliwei Communications Inc.© 2010 | All rights reserved